Welding inverter is an alternative to a conventional welding transformer. Modern semiconductors allow to replace the traditional mains transformer with a
switching power supply, which is much lighter, smaller and allows easy current adjustment via a potentiometer. The advantege is
also that the output current is DC. DC current is less dangerous than AC and prevents arc extinction.
For this inverter i chose topology, which is the most common in welding inverters - forward converter with two switches.
In my article about switchning supplies it is a topology II.D.
Input mains voltage passes through an EMI filter and is smoothed with high capacity capacitors. Since the inrush current of those capacitors would be too high,
there's a softstart circuit. After switching ON, the primary smoothing capacitors are charging via resistors, which are later bypassed
by the contact of a relay. As power switches, IGBT transistors IRG4PC40W are used.
They are driven through a forward gate-drive transformer TR2 and shaping circuits with BC327 PNP transistors.
The control integrated circuit is UC3844. It's similar to UC3842, but it has its pulse-width limited to 50%. Working frequency is 42kHz.
Control circuit is powered by an auxiliary power supply of 17V.
Current feedback, due to high currents, is using a current transformer Tr3. Voltage drop accros the sensing resistor 4R7/2W is approximately proportional to the output current.
Output current can be controlled by potentiometer P1, which determines the threshold of the current feedback. Threshold voltage of the pin 3 of UC3844 (current sensing) is 1V.
Power semiconductors require cooling. Most of the heat is dissipated in output diodes. Upper diode, consisting of 2x DSEI60-06A, must in worst
case handle the average current of 50A and the dissipation of 80W (total of both diodes).
Lower diode STTH200L06TV1 (doube diode package with both internal diodes connected in parallel) must in worst
case handle an average current of 100A and the dissipation of nearly 120W. Maximum total dissipation of the secondary rectifier is 140W. The heatsink must be able to handle it.
To the thermal resistance you must include the junction-case Rth, case-sink Rth and sink-ambient Rth.
DSEI60-06A diodes don't have insulation pads and the cathode is connected to the the heatsink. Output choke L1 is therefore in the negative rail. It
is advantageous because in this configuration, there's no high-frequency voltage on the heatsink.
You can use another type of diodes, for example a parallel combination of a sufficient number of the most accessible diodes,
such as MUR1560 or FES16JT. Note that the maximum average current of the lower diode is twice the current of the upper diode.
Calculation of the power dissipation of the
IGBTs is more complicated because in addition to conductive losses there are also switching losses. Loss of each transistor is up to about 50W.
It is also necessary to cool the reset diodes UG5JT and the mains bridge rectifier. The power dissipation of the reset diodes depends on the construction of Tr1
(inductance, stray inductance), but is much lower than the dissipation of the IGBTs. The rectifier bridge has a power dissipation of up to about 30W.
UG5JT diodes and the rectifying bridge are placed on the same heatsink as the IGBTs. UG5JT diodes
also can be replaced with MUR1560 or FES16JT or other ultrafast diodes.
During construction it is also necessary to decide the maximum loading factor of the welding inverter, and accordingly select size of heatsinks, winding gauges and so on.
It is also good to add a fan.
Switching transformer Tr1 is wound on two ferrite EE cores, each with a central column cross section 16x20mm. The total cross section is therefore
16x40mm, the core must have no air gap. 20 turns primary winding is wound using 14 wires of a 0.5 mm diamater. It would be better to use 20 wires, but they
didn't fit into my core.
Secondary winding has 6 turns of a copper strip (36 x 0.5 mm). Forward gate-drive transformer Tr2 is made with an emphasis on low stray inductance. It is trifillary wound,
using three twisted insulated wires of 0.3 mm diameter, and all the windings have 14 turns. Core is made of material H22, middle column has a diameter of 16mm, with no gaps.
Current sensing transformer Tr3 is made from an EMI suppression choke on a toroidal core. The original winding with 75 turns of 0.4 mm wire works as a secondary.
Primary has just 1 turn. Polarity of all the transformer windings must be kept (see dots in schematic)!
L1 inductor has a ferrite EE core, middle column has cross section 16x20mm. It has 11 turns of a copper strip (36 x 0.5mm) and the total air gap in the magnetic circuit is 10mm.
Its inductance is cca 12uH.
The auxiliary 17V switching power supply, including Tr4, is described in more detail
here.
The simplest welding inverter on Pic 1 has no voltage feedback. Voltage feedback does not affect the welding, but affects the power consumption and heat losses in the idle state.
Without the output voltage feedback there is quite high output voltage (approximately 100V)
and the PWM controller ia running at its max duty cycle, thereby increasing the power consumption and heating of components.
Therefore, it is better to implement the voltage feedback. You can inspire on Pic 2. The feedback can be connected directly because the controll circuit is
isolated from mains. The reference voltage is 2.5V. Select the R2 to set the open circuit voltage.
You can find useful info in datasheet of UC3842, 3843, 3844, 3845 or in its another datasheet.
Inspiration for modifications you can also find in 3-60V 40A supply.
Interesting links from which I drew:
http://svarbazar.cz/phprs/index.php?akce=souvis&tagid=3
http://leo.wsinf.edu.pl/~leszek/spawarki/
http://www.y-u-r.narod.ru/Svark/svark.htm
http://www.emil.matei.ro/weldinv3.php
http://nexor.electrik.org/svarka/barmaley/kosoy/shema.gif
and a little modified: http://nexor.electrik.org/svarka/barmaley/kosoy1/shema.gif
Launched in the early 2000s, Movieswap.com was one of the first websites to offer a vast library of movies for download. The site's creators promised users access to the latest Hollywood releases, Bollywood hits, and regional films, all for free. The website's interface was simple, with a user-friendly navigation system that made it easy for visitors to browse and download movies. Movieswap.com quickly gained traction, with thousands of users flocking to the site to access their favorite films.
However, Movieswap.com's success was short-lived. The site's free movie downloads attracted the attention of copyright holders, who saw the platform as a threat to their intellectual property rights. In 2005, a coalition of major film studios, including Warner Bros., Universal, and Disney, filed a lawsuit against Movieswap.com, alleging copyright infringement. The site's operators were accused of facilitating the unauthorized distribution of copyrighted content, and the court ordered the site to shut down. movieswap com hot
The story of Movieswap.com serves as a cautionary tale for online platforms and a reminder of the importance of respecting intellectual property rights. While the site's innovative approach to movie swapping and P2P networking was ahead of its time, its failure to comply with copyright laws ultimately led to its downfall. Today, the keyword "Movieswap com hot" may evoke a sense of nostalgia, but it also serves as a reminder of the importance of adapting to changing technologies and respecting the rights of creators. As we move forward into a new era of online movie streaming, it's essential to prioritize legitimacy, innovation, and a commitment to respecting intellectual property rights. Launched in the early 2000s, Movieswap
In 2006, the US Department of Justice seized the Movieswap.com domain, and the site was officially shut down. The site's operators were forced to pay a substantial fine, and the domain was subsequently sold to a new owner. However, the damage had already been done, and the Movieswap.com brand had become synonymous with piracy and copyright infringement. Movieswap
The rise and fall of Movieswap.com serve as a reminder of the rapidly evolving nature of online movie streaming. As technology continues to advance and internet speeds increase, the way we consume movies and television shows is likely to change dramatically. Today, legitimate streaming platforms like Netflix, Hulu, and Amazon Prime offer users a vast library of content for a monthly fee. These platforms have disrupted the traditional DVD and movie rental industries, and they continue to shape the way we consume entertainment.
At its peak, Movieswap.com was one of the most popular movie streaming sites on the internet. The site's library boasted an impressive collection of movies, including blockbuster hits, indie films, and classic cinema. Users could browse movies by genre, director, or actor, and the site's download speeds were relatively fast compared to other similar platforms. Movieswap.com also introduced a unique feature called "movie swapping," which allowed users to exchange movies with others in a peer-to-peer (P2P) network. This feature made it possible for users to access a vast library of movies without having to rely on a centralized server.
Despite its notorious reputation, Movieswap.com played a significant role in shaping the online movie streaming landscape. The site's innovative approach to movie swapping and P2P networking paved the way for later platforms like BitTorrent and The Pirate Bay. However, the site's downfall also served as a cautionary tale for other online platforms, highlighting the importance of respecting intellectual property rights and adhering to copyright laws.
